August Lock: Beeping Twice and Flashing Green Light... | digitalhomefaults.org

Technical Background:

The August Lock communicates via Bluetooth and Wi-Fi (via the August Connect module, if installed). It relies on a DC motor to actuate the deadbolt. The green LED typically indicates a communication or power-related issue. The beeping pattern is an error code signaling a specific fault condition. The motor drive circuit draws approximately 500mA under normal load, peaking at 1A during initial engagement. Operating voltage range is 6V-9V DC.

Symptoms:

The August Lock emits two audible beeps accompanied by a flashing green LED. This may coincide with failure to lock/unlock via the mobile application, key fob or physical thumb-turn. Log entries may indicate a 'Motor Jam' or 'Low Battery' error.

Possible Causes:

Low Battery: Insufficient voltage to drive the motor, especially in cold Canadian winters where battery impedance increases significantly at -20°C to -40°C.
Motor Obstruction: Physical obstruction preventing full deadbolt extension (e.g., door frame warping due to temperature fluctuations causing mechanical binding).
Wireless Interference: 2.4 GHz Wi-Fi interference causing communication failure between the lock and the August Connect module or the user's smartphone (RSSI below -75dBm).
Damaged Motor: Internal motor failure preventing proper actuation.
Incorrect Door Handing: The lock may not have been properly configured for the door's swing direction.
Firmware Glitch: A temporary software error requiring a reset.

Solution:

1

Replace Batteries: Install a new set of high-quality alkaline batteries (e.g., Duracell Quantum) or lithium batteries optimized for cold weather performance. Observe polarity.
2

Check Door Alignment: Inspect the strike plate and door frame for any signs of misalignment or obstruction. Adjust the strike plate if necessary. Apply lubricant (e.g., silicone spray) to the deadbolt.
3

Verify Wi-Fi Connectivity: Use a Wi-Fi analyzer app (e.g., NetSpot) to check the 2.4 GHz Wi-Fi signal strength near the August Connect module (if installed). Ensure RSSI is above -70dBm. Try relocating the August Connect closer to the router.
4

Perform a Factory Reset: Consult the August Lock documentation for the factory reset procedure. This may require removing and re-adding the lock to your August account.
5

Check Door Handing: In the August app, verify that the door handing is correctly configured. Recalibrate if necessary.
6

Inspect Motor Wiring: (Advanced) With the batteries removed, carefully inspect the motor wiring and connectors for any signs of damage or corrosion. Use a multimeter to check for continuity.
7

Contact August Support: If the problem persists, contact August support for further assistance and warranty information.

Safety Warning:

Always disconnect power (remove batteries) before performing any maintenance or repairs on the August Lock. Do not attempt to disassemble the lock beyond what is described in the user manual. Improper handling of lithium batteries can lead to fire or explosion. Dispose of used batteries properly at designated collection points. Secure your Wi-Fi network with a strong password to prevent unauthorized access to your smart home devices.

Prevention:

- Battery Management: Replace batteries annually before the onset of winter. Monitor battery health in the August app. Consider using lithium batteries for enhanced cold weather performance. - Firmware Updates: Enable automatic firmware updates in the August app to ensure the lock is running the latest software. - Regular Maintenance: Inspect the door and strike plate for proper alignment and lubrication every six months. Clean the exterior of the lock with a damp cloth. - Network Monitoring: Periodically check the Wi-Fi signal strength near the August Connect module to ensure a stable connection. Consider assigning a static IP address to the August Connect for improved reliability on Bell Giga Hub or Rogers Ignite networks.

Expert Tip:

If the August Lock is unresponsive, try the three-tap reset sequence (remove one battery, tap the August logo three times, reinsert battery). This often clears minor glitches without requiring a full factory reset. Also, ensure your Bell Giga Hub or Rogers Ignite router's firewall isn't overly restrictive on IoT device traffic (mDNS/Bonjour may need specific allowances).

Frequently Asked Questions

•How do I check the battery level of my August Lock?

The battery level is displayed in the August app under the lock settings.

•What type of batteries does the August Lock use?

The August Lock typically uses four AA alkaline or lithium batteries.

•How do I perform a factory reset on my August Lock?

The factory reset procedure varies depending on the model. Consult the August Lock documentation or the August support website for detailed instructions.

August Lock: Beeping Twice and Flashing Green Light Troubleshooting

Technical Background:

Symptoms:

Possible Causes:

Solution:

Safety Warning:

Prevention:

Expert Tip:

Frequently Asked Questions

Frequently Asked Questions

•How do I check the battery level of my August Lock?

•What type of batteries does the August Lock use?

•How do I perform a factory reset on my August Lock?

Related Questions

Technical Background:

Symptoms:

Possible Causes:

Solution:

Safety Warning:

Prevention:

Expert Tip: